Some tasks prefer to run on certain workers. This may be because that worker holds data dependencies of the task or because the user has expressed a loose desire that the task run in a particular place. Occasionally this results in a few very busy workers and several idle workers. In this situation the idle workers may choose to steal work from the busy workers, even if stealing work requires the costly movement of data.
This is a performance optimization and not required for correctness. Work stealing provides robustness in many ad-hoc cases, but can also backfire when we steal the wrong tasks and reduce performance.
Criteria for stealing¶
Computation to Communication Ratio¶
Stealing is profitable when the computation time for a task is much longer than the communication time of the task’s dependencies.
We do not want to steal tasks that require moving a large dependent piece of data across a wire from the victim to the thief if the computation is fast. We end up spending far more time in communication than just waiting a bit longer and giving up on parallelism.
[data] = client.scatter([np.arange(1000000000)]) x = client.submit(np.sum, data)
We do want to steal task tasks that only need to move dependent pieces of data, especially when the computation time is expensive (here 100 seconds.)
[data] = client.scatter() x = client.submit(sleep, data)
Fortunately we often know both the number of bytes of dependencies (as
reported by calling
sys.getsizeof on the workers) and the runtime cost of
previously seen functions, which is maintained as an exponentially weighted
Saturated Worker Burden¶
Stealing may be profitable even when the computation-time to communication-time ratio is poor. This occurs when the saturated workers have a very long backlog of tasks and there are a large number of idle workers. We determine if it acceptable to steal a task if the last task to be run by the saturated workers would finish more quickly if stolen or if it remains on the original/victim worker.
The longer the backlog of stealable tasks, and the smaller the number of active workers we have both increase our willingness to steal. This is balanced against the compute-to-communicate cost ratio.
Replicate Popular Data¶
It is also good long term if stealing causes highly-sought-after data to be replicated on more workers.
Steal from the Rich¶
We would like to steal tasks from particularly over-burdened workers rather than workers with just a few excess tasks.
If a task has been specifically restricted to run on particular workers (such as is the case when special hardware is required) then we do not steal.
Choosing tasks to steal¶
We maintain a list of sets of stealable tasks, ordered into bins by computation-to-communication time ratio. The first bin contains all tasks with a compute-to-communicate ratio greater than or equal to 8 (considered high enough to always steal), the next bin with a ratio of 4, the next bin with a ratio of 2, etc.., all the way down to a ratio of 1/256, which we will never steal.
This data structure provides a somewhat-ordered view of all stealable tasks
that we can add to and remove from in constant time, rather than
with more traditional data structures, like a heap.
During any stage when we submit tasks to workers we check if there are both idle and saturated workers and if so we quickly run through this list of sets, selecting tasks from the best buckets first, working our way down to the buckets of less desirable stealable tasks. We stop either when there are no more stealable tasks, no more idle workers, or when the quality of the task-to-be-stolen is not high enough given the current backlog.
This approach is fast, optimizes to steal the tasks with the best computation-to-communication cost ratio (up to a factor of two) and tends to steal from the workers that have the largest backlogs, just by nature that random selection tends to draw from the largest population.
Transactional Work Stealing¶
To avoid running the same task twice, Dask implements transactional work stealing. When the scheduler identifies a task that should be moved it first sends a request to the busy worker. The worker inspects its current state of the task and sends a response to the scheduler:
If the task is not yet running, then the worker cancels the task and informs the scheduler that it can reroute the task elsewhere.
If the task is already running or complete then the worker tells the scheduler that it should not replicate the task elsewhere.
This avoids redundant work, and also the duplication of side effects for more exotic tasks. However, concurrent or repeated execution of the same task is still possible in the event of worker death or a disrupted network connection.
Disabling Work Stealing¶
Work stealing is a toggleable setting on the Dask Scheduler; to disable
work stealing, you can toggle the scheduler
"False" either by setting
or through your Dask configuration file